手持式废纸包水分测定仪TK100M:SANTEST_GYcAT位移传感器_物位传感器

更新时间：2026-09-17 15:15:54

手持式废纸包水分测定仪TK100M

访问量：839
型号：TK100M
品牌：青岛拓科
MS7200+纸制品水分测定仪，主要用来测量各类纸筒,废纸纸包，纸卷等的水分含量。该仪器采用先进的美国集成电路传感技术和国际先进的电子元器件研制而成，测量精确度高，性能稳定，是家具、造纸、印刷、包装、建筑等行业检测其产品水分含量的理想选择。一、概述 1.美国进口集成电路技术。采用了温、湿度补偿技术，测量精确度高、稳定性好。 2.宽屏数字背光显示，即使光线不足的环境下也能清晰地显示测量读数。 3.测量速度快,可替代传统烘箱法，使水分测定时间缩短，测量值1秒钟读数，大大节省了检测人员的宝贵时间。 4.体积小，重量轻、抗干扰性能强、可随身携带便于现场进行快速检测。 5.仪器设计采用了低功耗大规模集成电路和液晶显示技术, 耗电量低. 6.报警功能，最大值保持。

技术参数
1.显示方式：
4位LCD液晶数字显示
2.水分测量范围：0-95%
3.测量环境：
温度：-10℃-60℃
湿度：25%-80%
4.测量原理：
电导法，温度补偿
5.精确度：±0.5％n
6.分辩力：0.1
7.响应时间：1秒
8.电源：4节7号电池
9.体积：
主机：140mm×60mm×24mm
手柄：175mm×40mm×20mm(探针80mm,150mm可选)
10.净重：约175克
可测量种类:
CD00 普通吸湿性材料
CD01 硬纸板,纸箱等
CD02 废纸包,散纸包等
CD03 纸筒,纸罐,纸管等
CD04 高吸湿性材料
可选附件：
校准器SANTEST_GYcAT位移传感器_物位传感器SANTEST_GYCRP位移传感器_GYCRS位移传感器 SANTEST-GYSE-A 线性位移传感器数显电子拉力机，橡胶拉力机，金属拉力机 SANTEST日本SANTEST代理SANTEST-GYCAT4.GYKM-LT位移传感器_GYKM-LS位移传感器

SANTEST_GYcAT位移传感器_物位传感器

型号：GYcAT
品牌：SANTEST
SANTEST_GYcAT位移传感器_物位传感器
SANTEST_GYcAT-Shanghai Hangou Mechanical And Electrical Equipment Co。，Ltd
GYCAT是日本SANTEST公司生产的线性位移传感器，传感器行程：15mm~2500mm，高精度，高品质

Thanks to the Surface Mount Technology, the entire signal
processing electronics of GYcAT series is integrated into a
transducer head.
You can get a voltage or current analog signal proportional to a
magnet position only by applying a 24V dc power supply directly to
the transducer.
GYcAT series have alarm output and head is equipped with noise
cancellation functions.
Non-linearity < ±0.05%FS TYP
Resolution < 0.01%FS
Repeatability < ±0.01%FS
Temp drift 40ppm FS/°C
Voltage output 0-10V or 10-0V / (output current:Max.5mA, load:Min.2kΩ)
Current output 4-20m or 20-4mA / (load:Min.500Ω)
Alarm output Open collector　30V　0.1A
Power supply +24 (±2) VDC (100mA)
Frequency response Std 1kHz (depending on stroke) sampling
Admissible press. 35MPa (probe rod)
Operating Temp -20°C-+65°C
Storage Temp -40°C-+80°C
Vibration 6G (or 40Hz 2mmPP)
Shock 50G (2msec)
Protection IP65
The above mentioned accuracy applies to sensors with an effective stroke of 300mm or more.
Model No.

(1):Effective Stroke
15mm-2500mm
(2):Output
A:0-10V
B:4-20mA
C:others (bipolar etc)
(3):Direction of output
(toward probe tip)
D:output data increase
R:output data decrease
(4):Thread
M:M24xP1.0 (Standard)
N:M18xP1.5
U:3/4-16UNF
(5):Sensor rod diameter
blank:Φ10 (Standard)
8:Φ8
14:Φ13.8
(6):Cable connection
CN:Connector (Standard)
G*:Pigtail type
(*:Cable length [m], Standard:1.5m)
Connector:straight type
Connector:only counter connector is supplied. In case cable needed,specify cable length.
Dimensions
Connector type (Standard)

Material probe head:Al diecast, probe rod:SS304
Standard magnet:No.2P. Other magnets are available from Magnet Grouping [B].
The tip dead zone length (70mm) depends on the magnet or float type.
The length of the cable should be less than 10m in case of using the voltage output type
and 100m in case of using the current output type.
Connector:Sanwa SNW-1607-PCF (Material:zinc alloy fluoroplastic)
Applied cable diameter:Φ6.6-Φ7.5
Wire size:Less than 0.5mm2
Connection
1 DC24V
2 NC
3 0V
4 SIG COM
5 Voltage output
6 (Current output)
7 Alarm output
*Shield should be connected with 0V at user side.