| 会员中心 | 设为首页 | 添加收藏 |
 |
| 当前位置：首页 > 供应信息 > 产品信息 > |
OH41 Hall effect Latch IC:OH44 Unipolar Hall Effect Switch IC |
更新时间：2026-10-18 17:53:24 |
OH41 Hall effect Latch ICOH41 Hall effect Latch IC General Description Part Number: OH41 Operate temperature: -40～150℃ Package: 1000pcs/bag OH41 Hall effect Latch Switch IC is composed of a reverse protector, voltage regulator, Hall voltage generator, differential amplifier, Schmitt trigger and an open-collector output on a single silicon chip. It can convert the magnetic field signal into digital voltage output, in response to N and S alternating magnetic field. Applications Non-contact switch Speed measurement Position detection Brushless DC motor Features High reliability Good temperature performance Anti-environmental stress Reverse Polarity Protection Absolute Maximum Ratings （TA=25℃） Supply Voltage VCC••••••••••••••4.5-24V Operating Temperature Range TA •••••••••••••••-40～150℃ Output Current IO•••••••••••••••••••25mA Storage Temperature RangeTS ••••••••••••••••-65～150℃ al Application Circuits： Precautions of OH Series Hall ICS Hall ICs are sensitive devices which performance could be influenced in some extent by magnetic, optical, thermal and mechanical stress. 1) A pull-up resistor RL should be connected between the power supply (Vcc) and the output (Vout) since most of hall ICs are open collector output (OC output) circuits, such as OH44E, OH137, OH513, OH543. Hall ICs with Build-in Resistor are not necessary to add one, for example OH921. 2) Avoid reversing the power supply (Vcc) and the output (Vout) as well as no overload use. Be careful of the burn and damage caused by instant large current and instantaneous high voltage. 3) The Protection circuit should be added in the test circuits of hall ICs, such as large capacitor and a voltage stabilizing diode, which could absorb the effects of the external circuit and power fluctuation. 4) Try to minimize the mechanical stress applied to the device and leads during the installation, especially on the pins where close to the root of the device when bending shaping etc. 5) Strictly regulate the welding temperature and time. When manual welding, the temperature of soldering iron shall not exceed 260℃and time should be less than 3 seconds. 6) When designing, please fully consider the influence factors of temperature, magnetic field attenuation, the movement way, etc. OH44 Unipolar Hall Effect Switch IC1116-090-463 DEUBLIN 江苏现货供应. 江苏现货供应1205-000-025 DEUBLIN旋转接头AX115CE磁性开关现货 ES008征能钳形电流互感器ES020征能钳式电流互感器 |
OH44 Unipolar Hall Effect Switch ICOH44 Unipolar Hall Effect Switch IC General Description: Part No.: OH44 Operate temperature: -40～125℃ Package: 1000pcs/bag OH44 Hall switch IC is internally consisted by reverse voltage protection device, voltage regulator, hall voltage generator, a differential amplifier, Schmitt trigger and the open collector output level, which can change magnetic field signal into digital voltage output. With the typical feature of small size and stable performance, OH44 is widely used in all kinds of position control, speed detection, flow detection occasions as a non-contact switch. Features 4V to 24V DC operation voltage Open-Collector pre-driver 25mA maximum sinking output current. Reverse Polarity Protection Applications Speed measurement Home appliances Position detection Flow measurement Absolute Maximum Ratings （TA=25℃） Supply Voltage VCC••••••••••••••3.5-30V Operating Temperature Range TA •••••••••••-40～125℃ Output Current IO•••••••••••••••••••25mA Storage Temperature RangeTS ••••••••••••••••-55～150℃ Precautions of OH Series Hall ICS Hall ICs are sensitive devices which performance could be influenced in some extent by magnetic, optical, thermal and mechanical stress. 1) A pull-up resistor RL should be connected between the power supply (Vcc) and the output (Vout) since most of hall ICs are open collector output (OC output) circuits, such as OH44E, OH137, OH513, OH543. Hall ICs with Build-in Resistor are not necessary to add one, for example OH921. 2) Avoid reversing the power supply (Vcc) and the output (Vout) as well as no overload use. Be careful of the burn and damage caused by instant large current and instantaneous high voltage. 3) The Protection circuit should be added in the test circuits of hall ICs, such as large capacitor and a voltage stabilizing diode, which could absorb the effects of the external circuit and power fluctuation. 4) Try to minimize the mechanical stress applied to the device and leads during the installation, especially on the pins where close to the root of the device when bending shaping etc. 5) Strictly regulate the welding temperature and time. When manual welding, the temperature of soldering iron shall not exceed 260℃and time should be less than 3 seconds. 6) When designing, please fully consider the influence factors of temperature, magnetic field attenuation, the movement way, etc. |
 |
热门产品 |  |
 |
|