油库专用柴油泄漏报警器规格/价格/厂家:OH13 Hall Effect Latch IC

更新时间：2026-05-28 09:35:35

油库专用柴油泄漏报警器规格/价格/厂家

访问量：332
型号：RBT-6000
品牌：赛弗
油库专用柴油泄漏报警器规格/价格/厂家柴油气体探测器是工业用可燃气体气体安全检测仪器，适用于化工、户外灌区等环境下，LCD状态指示灯（电源、报警、故障）显示，控制器在线校零、标定。两线制无极性供电和信号传输，安装简单，布线方便。固定式柴油气体浓度报警器分为气体探测器（放现场）和油库专用柴油泄漏报警器规格/价格/厂家气体报警控制器（放人员值班室），中间两芯屏蔽线连接，布线非常简单；控制器可时时显示现场气体浓度，当气体浓度达到设定的低报警点时，控制器可发出声光报警，提示工作人员现场浓度过高，以提醒用户采取安全措施，并驱动排风、切断、喷淋系统，防止发生爆炸、火灾、中毒事故，从而保障安全生产。产品广泛应用于燃气、石油、化工、冶金等存在易燃、易爆气体的危险场所。

柴油气体报警器产品特点:
RBK-6000使用高速CPU处理器，能够快速精确地处理系统任务，保证系统的可靠性。
可通过计算机实现本地监控及远程监控，探头器运行状态数据可永久存储
LCD液晶屏幕，可实时显示探头器的浓度、状态。
实现可燃与毒性气体探头器的混合配置。
采用模块化结构设计，便于系统维护。
选购配件

济南赛弗仪器仪表有限公司柴油报警器专业生产厂家,公司专业生产：各种可燃有毒有害气体泄漏报警器,气体检测仪器，在线式固定式、手持式，便携式可燃气体检测仪。
（TEL：0531-68658013，15154173891联系人：葛经理）

OH13 Hall Effect Latch IC可程式恒温恒湿箱价格可程式恒温恒湿箱厂 CDLF型轻型多级离心泵DAY6000开关柜智能操控单元租赁Agilent安捷伦 E4438C 矢量信号发生器租赁莱特波特IQ2010蓝牙wifi测试仪

OH13 Hall Effect Latch IC

型号：OH13
品牌：欧卓 OUZHUO
OH13 Hall Effect Latch IC
General Description
Part No：OH13 Operate temperature：-40～150℃ Package：1000pcs/reel

OH13 Hall effect Latching Switch IC integrates hall element and signal processing circuit in one silicon chip, including a reverse protector, voltage regulator, Hall voltage generator, differential amplifier, Schmitt trigger and an open-collector output. It can work with the multi-polar magnetic ring and alternating magnetic fields. OH13 has better anti-interference ability and the output waveform duty ratio is little affected by external temperature and alternating magnetic field.

Features
 High reliability
 High sensitivity
 Good temperature performance
 Anti-environmental stress
Applications
 The brushless DC motor internal reversing
 The motor speed and direction detection
 The motor of electric bicycle, power assisted device
 Speed sensor, counter
 The flow sensor, flow meter

Absolute Maximum Ratings （TA=25℃）
Supply Voltage VCC••••••••••••••4-30V
Operating Temperature Range TA ••••••••-40～150℃ Output Current IO•••••••••••••••••••50mA Storage Temperature Range TS ••••••••••••••••-55～150℃

Precautions of OH Series Hall ICS
Hall ICs are sensitive devices which performance could be influenced in some extent by magnetic, optical, thermal and mechanical stress.
1) A pull-up resistor RL should be connected between the power supply (Vcc) and the output (Vout) since most of hall ICs are open collector output (OC output) circuits, such as OH44E, OH137, OH513, OH543. Hall ICs with Build-in Resistor are not necessary to add one, for example OH921.
2) Avoid reversing the power supply (Vcc) and the output (Vout) as well as no overload use. Be careful of the burn and damage caused by instant large current and instantaneous high voltage.
3) The Protection circuit should be added in the test circuits of hall ICs, such as large capacitor and a voltage stabilizing diode, which could absorb the effects of the external circuit and power fluctuation.
4) Try to minimize the mechanical stress applied to the device and leads during the installation, especially on the pins where close to the root of the device when bending shaping etc.
5) Strictly regulate the welding temperature and time. When manual welding, the temperature of soldering iron shall not exceed 260℃and time should be less than 3 seconds.
6) When designing, please fully consider the influence factors of temperature, magnetic field attenuation, the movement way, etc.