布莱迪160位式控制压力表YXK-160:布莱迪充油耐震压力表YTN-041/051

更新时间：2026-09-27 13:17:08

布莱迪160位式控制压力表YXK-160

产品简介
YXK-160 位式控制压力表采用弹簧管作为测压敏感元件，在对被测流体介质压力进行控制（输出通断信号）的同时，可同步指示出被测压力值。
该仪表的控制和指示系统分别由相互独立的弹簧管带动，性能稳定可靠。并使用大功率微动开关，可对一般机械设备进行直接控制。
Brief
YXK-160 bit type control pressure gauge use the bourdon tube as the snsitive element, while controllingthe liquid medium pressure (export switching signal), itcan indicate the pressure value.
The control and indication system are lead byseparate bourdon tube, have stable performance. Andit use high efficient microswitch, may control directcommon mechanical device.
工作原理
该仪表由控制系统和指示系统两部分组成，分别由独立的弹簧管带动。弹簧管在被测压力作用下，产生弹性变形引起管端位移，其位移通过机械传动机构（连杆和机芯）进行放大，传递给示值部件，指针在刻度盘上指示出相应的压力值。同时，弹簧管产生弹性变形引起的管端位移推动微动开关的触头产生相应的切换动作即通/断信号，这样可在设备达到设定压力时发出所需的报警信号或开、停机等控制压力的动作，将系统压力控制在所需范围内。
Operating principles
In strument is made up of control and indication system, which are lead by separate bourdon tube. The deformation of bourdon tube under the measuring pressure causes pipesport displacement, which is enlarged by mechanical transmission organizations (connecting rod and movement). Communicating to value-show components. Then the value of the pressure is indicated. At the same time, the tube ends moving caused by the deformity bourdon tube of make the microswitch contacts to make or break the signal, so it can make alarm or turn on / off the device to keep the pressure in the required range.
主要技术参数Main technic index
公称直径 φ 160mm Diameter: φ 160mm
指示精确度 ± 1.5% Accuracy: ± 1.5%
设定精确度 ± 2.5% Set accuracy: ± 2.5%
切换差 6%～15% Difference of switch: 6%～15%
测量范围 0～0.1 至0～25MPa 各系列 Range: 0～0.1 to 0～25MPa (for all)
-0.1～0.15 至-0.1～2.4MPa 各系列 -0.1～0.15 to -0.1～2.4MPa (for all)
接点形式大功率微动开关 Contacts mode: Large power microswitch
接点数量 1 或2 个 Quantity of contacts: 1 or 2
接点最大容量 AC 220V × 15A Maximum capacity of contacts: AC 220V × 15A
AC 380V × 8A AC 380V × 8A
DC 24V × 1.5A 阻性负载 DC 24V × 1.5A resistant load
测压部件材质接头：SUS316 Part materials of measurement pressure:
测压元件：SUS316L Socket SUS316
Element of measurement pressure: SUS316L
外壳材质铸造铝合金（黑色） Materias of case: foundry aluminium alloy (black)
仪表玻璃有机玻璃 Glasses: Organic glass
工作环境条件温度：-25℃～+55℃ Working ambient conditions Temperature:-25℃～+55℃
湿度：＜ 95% Humidity: ＜ 95%
防护等级 IP54 Protection class: IP54
绝缘电阻不小于20M Ω Insulating resistance: not less than 20M Ω
绝缘强度 50Hz 1500VAC 耐压1min Insulating strengthness:
50Hz 1500VAC pressure-resistant 1min布莱迪充油耐震压力表YTN-041/051布莱迪径向螺钉上紧式压力表 Y-050. 200 布莱迪小外径不锈钢密闭型压力表YTFS-040差压表江苏金工美国福禄克TIS10红外热像仪美国福禄克TiS20红外热像仪

布莱迪充油耐震压力表YTN-041/051

产品特性：
●径向或轴向接头两件式结构
●旋压密封罩壳设计
● 304本色钢外壳铜内机、钢内机可选
●充液耐震，密闭干式可选
● 2.5%精度等级
●测量范围：
铜内机：0.1MPa～25Mpa
钢内机：0.16MPa～25Mpa

CHARACTERISTICS
● Bottom mounting or Back mounting, two-piece type
● Roll formed
● 304 original color case, brass and Stainless Steel case available
● Liquid filling, Vibration-proof, Obturation and dry type available
● Accuracy2.5%
● Range Brass internals: 0.1MPa～25MPa
Stainless Steel internals: 0.16MPa～25MPa
压力表/耐震压力表YTN-41/YTN-51/
轴向耐震压力表YTN-41Z/YTN-51Z